Automatic Vertical Mineral Fuel Oil Disc Stack Centrifuges Separator 4KW

Automatic Vertical Mineral Fuel Oil Disc Stack Centrifuges Separator 4KW

Descriptions

Model PDSD3000F-B1215Z separator is mainly used to remove water and mechanical impurities from fuel oil, lubricating oil and other mineral oil in marine diesel engine unit and land-used diesel generator unit of power station so as to reduce wear of the diesel engine and other machine, and prolong engine life.

The model is also used to separate two unsolvable liquids with different specific gravity or remove small amount of solid particle from liquid.

The machine adopts automatic control, it has the advantages of high efficiency, low oil consumption, convenient operation and economic maintenance cost. 

The clear oil and dirty water are pumped out by centripetal pump, the sludge is discharged automatically and fully.

The machine is one kind of rotary machine with high speed, After accurate dynamic balancing, it can run for long time with low vibration, safety and security.                                  

The design, product and acceptance are conformed to the standard of GB/T5745 “Marine Disc Separator”.      
 

Advantages:

•  Automatic piston type slag removal
• Modular design
•  Automatic operation

Automatic Control System:

Water Control: Automatic control unlocking water, sealing water and water-seal/water switching.

Pneumatic Control: Filter and adjust compressed air, control three-way changeover pneumatic valve.

Temperature Control: Automatic control the temperature of the oil line, also control separately or with electric control cabinet at the same time.
Buzzer Control: Monitor oil temperature, pressure, over loading, non-discharging and leaking, and offer a group of passive contactor stretching out to control panel.

Condition for mineral oil separation and actual capacity (refer to the chart)

Main Technical Specification

The Whole Unit Consists of:

1. Separator   2. Screw pump   3.Electric control box  4. Steam heater  5. Temperature adjusting valve

6. High temperature ball valve  7. Steam trap  8. Temperature sensor  9. Pneumatic Three-way valve     

10. Stop-check valve     11. Oil filter     12. Vacuum gauge     13. Pressure gauge 

14. Air pressure reducing valve 15. 3/2 Solenoid valve  16. Ball valve  17. Brass filter ball valve  

18. Water pressure reducing valve        19. 2/2 Solenoid valve  20. 2/2 Solenoid valve 

21. Pressure switch   22.Skid

Technical analysis:

Peony's Disc separator technology comparison with foreign companies

Cost Analysis :

Compared selling price and maintenance cost with , Westfalia

            and other domestic manufacturers

Value Analysis:

According to the requirements of each classification society, all modules are equipped with oil leak alarm and high temperature alarm.

Oil.hydraulic,pneumatic control part adopts the Brand Baode (Germany).

Heater adopts brand SWEP (Germany).

Pressure control adopts Korean products or products

Screw pump is used instead of gear pump.

All equipped with automatic temperature control device (Made by the RTK production in Germany or made in China)

The main electrical components of standard electrical control box are produced by Schneider

company while PLC is produced by Siemens or Mitsubishi.

The complete sets referred above are all Peony’s production of automatic Standard Controls and we certainly can modify the configuration list according to customers’ specified requirements.

Principle and structure

Disc separator is vertical centrifuge. The drum is installed on the upper side of the vertical shaft. Driven by the motor, it will rotate at a high speed through the gearing. Inside the drum there is a group of dish parts overlaying each other – disc. There is very small gap between the disc. Suspension (or emulsion) is fed into the drum through the inlet in the middle of the drum. When the suspension (or emulsion) flows through the gap between the disc, under the action of the centrifuge, the solid particles (or droplets) go down to the disc in the formation of sediment (or liquid layer). Along the disc surface, the sediment slides out of the disc and accumulates at the part with the largest diameter inside the drum. After the separation, the liquid is discharge out of the drum from the drain outlet. The role of the disc is to reduce the sediment distance of solid particles (or droplets) and enlarge the sediment area of the drum. With the disc inside the drum, the capacity of the separator is improved greatly. The solid gathering inside the drum is manually removed by taking apart the drum after power off, or discharges from the drum through the slag-off part with the separator power on.

Guarantee:

Peony has advantages in price, service and quality.We have Military Product Quality System Certification, CE certificate,Quality System Certification,many professional equipments and advanced designs.